/
elproMONITOR Settings (EN)

elproMONITOR Settings (EN)

Information

Important information and warnings

DELETE

Windows function, e.g. Delete

<xxxxxx>

Syntax for placeholders.
Placeholders are written between < > characters.

>>

Reference to a further chapter or document.

The representation refers only to a part of the user interface.

In the interest of our clientele, we reserve the right to make changes due to technical advances. Therefore, schematics, descriptions and scope of delivery may be changed without prior notice. This manual is valid as of version 2017.

Liability

  • In no event shall ELPRO-BUCHS AG be liable for any direct, indirect, special, incidental, consequential or punitive damages or losses, including lost profits and data, arising out of the use of your data loggers, sensors, accessories, software products or the information contained in the documentation.

  • ELPRO-BUCHS AG does not bear any responsibility for the installation of the software products.

  • ELPRO-BUCHS AG makes no warranties of any kind, express or implied, regarding the merchantability and fitness of your products for any particular purpose.

  • In the interest of our clientele, we reserve the right to make changes and discontinuations due to technical advances. Therefore functionality, schemes, descriptions and scope of delivery can be changed without prior notice!

  • Because some countries or states do not allow the limitation of the term implied warranty or disclaimer of incidental or consequential damages, the limitations and exclusions may not apply to every purchaser. If any provision of this warranty is held invalid or unenforceable by a court of competent jurisdiction, it will not affect the validity or enforceability of the remaining provisions.

  • ELPRO-BUCHS AG accepts no liability for transport damage or any consequential damage resulting therefrom.

  • In general, the legal provisions of Switzerland apply. The place of jurisdiction is the district court of Werdenberg-Sarganserland.

Warranty

  • The warranty obligations are limited, at ELPRO-BUCHS AG's discretion, to the repair, refund of the purchase price, repair free of charge or replacement of a defective product returned to ELPRO-BUCHS AG or a reseller approved by ELPRO-BUCHS AG within the warranty period.

  • There is no entitlement to free "on-site customer support" by an employee of ELPRO-BUCHS AG.

  • The warranty extends only to the original purchaser or end user and customers of a reseller authorized by ELPRO-BUCHS AG.

  • Resellers approved by ELPRO-BUCHS AG are not authorized to provide a greater or other warranty on behalf of ELPROBUCHS AG.

  • ELPRO-BUCHS AG grants a warranty period of 24 months on the following new products:

    • Data logger

    • Brackets

    • Accessories, except sensors and third-party products

  • This warranty applies to material defects or production defects.

  • ELPRO-BUCHS AG grants a warranty period of 6 months for the following products and services:

    • All service work and repairs

    • Temperature sensors

    • Humidity sensors

  • ELPRO-BUCHS AG grants a warranty period of 90 days that the medium on which the software product was delivered is free from defects in material and workmanship under normal conditions. The software product conforms in all material respects to the operating instructions and the information in the help file.

  • The warranty does not apply to consumables, disposable batteries or any other product which, in the opinion of ELPRO-BUCHS Ltd:

    • abused

    • changed

    • replaced by a wrong product

    • has been operated and damaged outside the specification due to accident or operating or handling conditions.

  • Wear and tear, cable breakage and corrosion cannot be claimed under warranty.

  • For third-party products, ELPRO-BUCHS AG grants at most the warranty period of the manufacturer.

  • For discontinued products, ELPRO-BUCHS AG provides warranty work and customer support only for a limited period of time.

  • Warranty repairs are generally only carried out at the factory (ELPRO-BUCHS AG) or at an agency recognized by the factory.

  • ELPRO-BUCHS AG does not provide any warranty regarding the standard or SCS calibration of the data loggers and sensors. The specified data correspond to the situation during the calibration process

Software

  • The software products of ELPRO-BUCHS AG are subject to internal quality regulations and are regularly validated within the factory. In the event of any program errors, bypassing the error is considered as elimination.

  • Software operating instructions do not contain instructions on the basic operation of a computer or on basic functions of the Windows® operating system. For information on how to operate your computer or operating system, please refer to the appropriate manuals for your computer.

Data loggers, sensors and accessories

  • ELPRO-BUCHS AG uses the highest quality standards and a certified quality management system according to ISO 9001 for the production of data loggers and their accessories.

  • For information on the operation of the data loggers and their accessories, please refer to the corresponding product documentation provided by ELPRO-BUCHS AG.

  • When installing data loggers, sensors and accessories, the locally applicable installation regulations must be observed.

  • For applications in potentially explosive atmospheres, the zone assignment specified by ELPRO-BUCHS AG as well as the application and safety instructions must be strictly observed.

  • In the event of a warranty claim, the customer will receive a repair cost estimate from ELPRO-BUCHS AG in order to issue the appropriate authorization before work commences.

  • The transport costs for a repair at ELPRO-BUCHS AG will be borne by the customer. DAP (value added tax) will be borne by ELPROBUCHS AG.

  • ELPRO-BUCHS AG reserves the right to charge the purchaser for costs of repairs/parts replacement.

  • After repair, the product will be returned to the buyer with return shipping charges billed to the buyer (FOB shipping location).

Trademark

  • All listed company and product names and their trademarks are the protected property of their respective owners.

CHANGES OR MODIFICATIONS TO THIS PRODUCT WILL VOID THE ETSI / FCC APPROVAL TO OPERATE THIS PRODUCT. THIS PRODUCT COMPLIES WITH PART 15 OF THE FCC REGULATIONS AND RSS-210 INDUSTRY CANADA. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THE PROUDUCT MUST NOT CAUSE HARMFUL INTERFERENCE. (2) THE PROUDUCT MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

  • This product is subject to CE marking.

  • The manufacturer guarantees the conformity of this product to the corresponding directives: EN 61000-6-2 : 2001 and EN 61000-6-4 : 2001

  • FCC ID: Z45-E11645398

  • IC: 9954A-E11645398

  • This product must be disposed of in accordance with WEEE (Waste electrical and electronic equipment, 2002/ 96/EC)!

image-20251112-145437.png

 

1. Overview Settings

In the SETTINGS, the parameters are specified which the elproMONITOR software uses for the current monitoring task. These parameters contain settings for

  • >> Device settings - Here all I/O modules for ECOLOG-PRO and the alarm interface as well as associated digital inputs, digital outputs, sensors and sensor groups are parameterized.

  • >> Profiles - All profiles for sensor limits (alarms, warnings), sensor faults, digital input profiles, receiver profiles, time control profiles, data destination profiles and data export profiles are managed here.

  • >> Application Tasks - This is where scheduled exports and connection Check Tasks are parameterized and managed.

  • >> Application Settings - Here you can make settings for Comment templates and Application Settings.

1.1. User Interface

The Settings overview is opened by clicking on the "Settings" menu item. The default view is the existing >> sensors of the >> device settings.

image-20250703-092658.png

 

A - Details

A left click on a specific line opens the detail view for this setting. The detail view includes a list of all objects from the previous menu (here sensors) and the details of the selected object (here freezer temperature 1). No changes can be made directly in the details, but it is possible to switch between the individual objects by making the appropriate selection with the mouse in the details view. (see 1 in the graphic)

image-20250703-093410.png

 

I - Devices Settings

The individual device settings can be parameterized in this area:

  • >> 2. Sensors

  • >> 3. Digital inputs

  • >> 4. Digital outputs

  • >> 5. Sensor groups

  • >> 6. I/O modules

  • >> 7. Bridges

II - Profiles

Profiles contain specifications for specific information that can be assigned to the devices:

  • >> Sensor limit profiles

  • >>Sensor issue profiles

  • >> Digital input profile

  • >> Recepient profiles

  • >> Schedule profiles

  • >> Data export profiles

III - Apptication Tasks

In the Application Tasks, Export Scheduled Tasks and Connection Check Tasks of the software are made:

  • >> Export Schedule Tasks

  • >> Connection Check Tasks

IV - Application Settings

In the Application settings, Comment Templates and Application Settings can be configured

  • >> Comment Templates

  • >> Application Settings

2. Sensors

The Sensors overview is opened by clicking on the "Sensors" menu item in the Settings menu.

image-20250703-113636.png

 

A - Details

With a left click on a certain line the detail view Sensors opens. The detailed view includes a list of all objects from the Sensors overview and the details of the selected object (here Freezer Temperature 1). The applicable functions for the selected sensor are described in III - Applicable functions and are:

  • Edit

  • Report

  • Close

    image-20250703-113907.png

     

B - Quick Links

The following Quick Links are available. (See III - Applicable Functions)

  • Edit

  • Retire

  • Delete

The Quick Links perform the function only for a single sensor regardless of the selected tick boxes.

I - Devices Settings

The Sensors overview is opened by clicking on the "Sensors" menu item in the Settings menu.

II - Detail Column

This area contains basic information about the sensors. The following information is available for each sensor:

  • Sensor - name of the sensor

  • I/O Module - name of the I/O module >> I/O Module

III - Applicable Functions

The following functionalities can be executed here.

Report

A >> elproMONITOR configuration report with all selected parameters is created.

The number of existing I/O modules, sensors, profiles and program settings determines the size (number of pages) of the configuration report created as *.pdf file.

Add new sensor

The details in the view are replaced by the following parameters for creating a new sensor:

 

 

 

 

General:

  • Sensor name
    Name of the sensor for monitoring with elproMONITOR and for easy identification in the reports. The sensor must be provided with a unique name.

  • Sensor status
    This is an information field that reflects the current state (Enabled / Disabled) of the sensor. This field cannot be changed. The sensor is activated / deactivated in the monitor manually or automatically during a calibration.

 

Connection:

  • I/O module
    Selection list with the available I/O modules. The sensor must be assigned to one of these I/O modules.

  • I/O module channel
    Selection list with all channels available at this I/O module. The sensor must be connected to one of these channels to receive its measured values. Only the channels that are still free are listed.

  • Associated digital output
    Selection list with the names of the available digital outputs. The sensor activates a digital output directly in the event of an error. (e.g. of an ECOLOG-PRO 4DO).

 

Recording:

  • Recording interval
    At a restart, the 1st measured value is recorded when the first full interval is reached.
    The recording of the data is synchronous. All measured values and statuses are recorded simultaneously. The interval can be specified individually for each sensor. The intervals 1, 2, 3, 4 , 5, 6, 10, 12, 15, 20, 30 and 60 minutes are possible.
    To correct the interval of an existing sensor, it must be deleted or decommissioned and then added again.

The recording interval cannot be changed subsequently.

The two channels of ECOLOG-PRO 1THR and 2TH are interleaved. Once one of them has been defined, no other recording interval can be selected for the other one.

  • Time control profile
    With a >> time control profile, the sensor can be controlled time-dependently for monitoring by elproMONITOR. An already defined profile can be selected from this selection list.

 

Description:

  • Sensor ID
    In addition to the sensor name, serves as a further parameter for identifying the sensor.

For digital sensors (e.g. ECOLOG-PRO 1THR) the sensor ID can also be read out from the sensor

  • Sensor note
    Text field for entering sensor-related information.

 

Profile Set A and Profile Set B:

The profile sets are used to assign the following >> profiles.

  • Profile for alarms due to limit violations.

  • Profile for receiver in case of alarms

  • Profile for warnings due to limit violations.

  • Profile for receiver in case of warnings

  • Profiles for sensor malfunctions

  • Profiles for receivers in the event of sensor malfunctions.

With >> Time control profiles it is possible to switch between Set A (default) and Set B. This is used to switch between different alarm limits, warning limits, evaluated sensor faults and the corresponding receiver groups.

 

 

List of existing sensor groups to which the sensor can be added or from which it can be removed.

 

image-20250703-120612.png

 

Calibration Adress The adress that calibration took place can be entered to this section

 

image-20250703-120642.png

 

Calibration Details

Necessary details for the calibration can be entered to this section

 

image-20250703-120704.png

 

Calibration Points

Calibration oints can be entered to this section

Retire

Opens the window for permanently retiring the selected sensor. No further data will be recorded. Retiring is only possible after selecting a comment template or entering a comment and authentication with the password.

The existing data is not deleted from the database and the analysis of historical data remains possible.
This action cannot be undone.

Delete

Opens the window for permanently deleting the selected sensor. No further data will be recorded. Deletion is possible only after selecting a comment template or entering a comment and authentication with the password.

The existing data from the database will be deleted and the analysis of the historical data is no longer possible.
This action cannot be undone.

Edit

The same parameters as in >> Add new sensor are displayed for editing.

The only limitation is that the recording interval cannot be changed afterwards.

Close

Closes the current window and returns to the Sensors overview.

3. Digital Inputs

The digital inputs overview is opened by clicking on the "Digital inputs" menu item in the Settings menu.

A - Details

With a left click on a certain line the detail view digital inputs opens. The detailed view includes a list of all objects from the digital inputs overview and the details of the selected object (here Door Contact 1). The applicable functions for the selected digital input are described in III - Applicable functions and are:

  • Report

  • Add new digital input

  • Shutdown

  • Delete

  • Edit

  • Close

B - Quick Links

The following Quick Links are available. (See III - Applicable functions)

  • Edit

  • Shutdown

  • Delete

The Quick Links perform the function only for a single digital input regardless of the selected tick boxes.

I - Devices Settings

The digital inputs overview is opened by clicking on the "Digital inputs" menu item in the Settings menu.

II - Detail Column

This area contains basic information about the digital inputs. The following information is available for each digital input:

  • Digital input name - name of the digital input

  • I/O Module - name of the I/O module >> I/O Module

III - Applicable Functions

The following functionalities can be executed here.

Report

A >> elproMONITOR configuration report with all selected parameters is created.

The number of existing I/O modules, sensors, profiles and program settings determines the size (number of pages) of the configuration report created as *.pdf file.

Add new digital input

The details in the view are replaced by the following parameters for creating a new digital input:

 

 

General:

  • Digital input name
    Name of the digital input for monitoring with elproMONITOR and for easy identification in the reports. The digital input must be provided with a unique name.

  • Digital input status
    This is an information field that reflects the current state (Enabled / Disabled) of the digital input. This field cannot be changed. The digital input is activated / deactivated in the monitor manually or automatically during a calibration.

 

 

Connection:

  • I/O module
    Selection list with the available I/O modules. The digital input must be assigned to one of these I/O modules.

  • I/O module channel
    Selection list with all channels available at this I/O module. The digital input must be connected to one of these channels to receive its measured values. Only the channels that are still free are listed.

Each digital input of an ECOLOG-4DI contains 3 channels:

  • n.1 - default (contact status at start recording interval)

  • n.2 - time monitoring (percentage duration during the recording interval)

  • n.3 - edge counter (number of contact status changes during the recording interval)

For more information see >> digital input profiles

  • Associated digital output
    Selection list with the names of the available digital outputs. The digital input directly activates a digital output in case of an error. (e.g. of an ECOLOG-PRO 4DO).

 

 

Recording:

  • Recording interval
    During a restart, the 1st measured value is recorded when the first full interval is reached.
    The recording of the data is synchronous. All measured values and statuses are recorded simultaneously. The interval can be specified individually for each digital input. The intervals 1, 2, 3, 4 , 5, 6, 10, 12, 15, 20, 30 and 60 minutes are possible.
    To correct the interval of an existing digital input, it must be deleted or decommissioned and then added again.

The recording interval cannot be changed subsequently.

The two channels of ECOLOG-PRO 1THR and 2TH are interleaved. Once one of them has been defined, no other recording interval can be selected for the other one.

  • Time control profile
    With a >> time control profile, the digital input can be controlled time-dependently for monitoring by elproMONITOR. An already defined profile can be selected from this selection list.

 

 

Description:

  • Digital input ID
    In addition to the digital input name, serves as a further parameter for identifying the digital input.

  • Digital input note
    Text field for entering input-related information.

 

 

Profile Set A and Profile Set B:

The profile sets are used to assign the following >> profiles.

  • Profile for alarms of digital inputs.

  • Profile for receiver in case of alarms

With >> Time control profiles, it is possible to switch between Set A (default) and Set B. This is used to switch between different alarms and the corresponding receiver groups.

 

 

List of existing sensor groups to which the digital input can be added or from which it can be removed.

The digital input must be assigned to at least one sensor group by clicking the "Add" button.

Digital inputs can also be assigned to several sensor groups, which are displayed under "Sensor group name".

Retire

Opens the window for permanently retiring the selected digital input. No further data will be recorded. The retire is only possible after selecting a comment template or entering a comment and authentication with the password.

The existing data is not deleted from the database and the analysis of historical data remains possible.
This action cannot be undone.

Delete

Opens the window for permanently deleting the selected digital input. No further data will be recorded. Deletion is possible only after selecting a comment template or entering a comment and authentication with the password.

The existing data from the database will be deleted and the analysis of the historical data is no longer possible.
This action cannot be undone.

Edit

The same parameters as in >> Add new digital input are displayed for editing.

The only limitation is that the recording interval cannot be changed afterwards.

Close

Closes the current window and returns to the Digital Inputs overview.

4. Digital Outputs

The digital outputs overview is opened by clicking on the "Digital outputs" menu item in the Settings menu.

A - Details

With a left click on a certain line the detail view digital outputs opens. The detailed view includes a list of all objects from the overview digital outputs and the details of the selected object (here Alarm Lights). The applicable functions for the selected digital output are described in III - Applicable functions and are:

  • Report

  • Add new digital output

  • Delete

  • Edit

  • Close

B - Quick Links