General:

• Sensor name
  Name of the sensor for monitoring with elproMONITOR and for easy identification in the reports. The sensor must be provided with a unique name.

• Sensor status
  This is an information field that reflects the current state (Enabled / Disabled) of the sensor. This field cannot be changed. The sensor is activated / deactivated in the monitor manually or automatically during a calibration.

Connection:

• I/O module
  Selection list with the available I/O modules. The sensor must be assigned to one of these I/O modules.

• I/O module channel
  Selection list with all channels available at this I/O module. The sensor must be connected to one of these channels to receive its measured values. Only the channels that are still free are listed.

• Associated digital output
  Selection list with the names of the available digital outputs. The sensor activates a digital output directly in the event of an error. (e.g. of an ECOLOG-PRO 4DO).

Recording:

• Recording interval
  At a restart, the 1st measured value is recorded when the first full interval is reached.
  The recording of the data is synchronous. All measured values and statuses are recorded simultaneously. The interval can be specified individually for each sensor. The intervals 1, 2, 3, 4 , 5, 6, 10, 12, 15, 20, 30 and 60 minutes are possible.
  To correct the interval of an existing sensor, it must be deleted or decommissioned and then added again.

• Time control profile
  With a >> time control profile, the sensor can be controlled time-dependently for monitoring by elproMONITOR. An already defined profile can be selected from this selection list.

Description:

• Sensor ID
  In addition to the sensor name, serves as a further parameter for identifying the sensor.

• Sensor note
  Text field for entering sensor-related information.

Profile Set A and Profile Set B:

The profile sets are used to assign the following >> profiles.

• Profile for alarms due to limit violations.

• Profile for receiver in case of alarms

• Profile for warnings due to limit violations.

• Profile for receiver in case of warnings

• Profiles for sensor malfunctions

• Profiles for receivers in the event of sensor malfunctions.

List of existing sensor groups to which the sensor can be added or from which it can be removed.

General:

• Digital input name
  Name of the digital input for monitoring with elproMONITOR and for easy identification in the reports. The digital input must be provided with a unique name.

• Digital input status
  This is an information field that reflects the current state (Enabled / Disabled) of the digital input. This field cannot be changed. The digital input is activated / deactivated in the monitor manually or automatically during a calibration.

Connection:

• I/O module
  Selection list with the available I/O modules. The digital input must be assigned to one of these I/O modules.

• I/O module channel
  Selection list with all channels available at this I/O module. The digital input must be connected to one of these channels to receive its measured values. Only the channels that are still free are listed.

• Associated digital output
  Selection list with the names of the available digital outputs. The digital input directly activates a digital output in case of an error. (e.g. of an ECOLOG-PRO 4DO).

Recording:

• Recording interval
  During a restart, the 1st measured value is recorded when the first full interval is reached.
  The recording of the data is synchronous. All measured values and statuses are recorded simultaneously. The interval can be specified individually for each digital input. The intervals 1, 2, 3, 4 , 5, 6, 10, 12, 15, 20, 30 and 60 minutes are possible.
  To correct the interval of an existing digital input, it must be deleted or decommissioned and then added again.

• Time control profile
  With a >> time control profile, the digital input can be controlled time-dependently for monitoring by elproMONITOR. An already defined profile can be selected from this selection list.

Description:

• Digital input ID
  In addition to the digital input name, serves as a further parameter for identifying the digital input.

• Digital input note
  Text field for entering input-related information.

Profile Set A and Profile Set B:

The profile sets are used to assign the following >> profiles.

• Profile for alarms of digital inputs.

• Profile for receiver in case of alarms

List of existing sensor groups to which the digital input can be added or from which it can be removed.

General:

• Digital output Name
  Name of the digital output for monitoring with elproMONITOR and for easy identification in the reports. The digital output must be provided with a unique name.

• I/O module
  Selection list with the available I/O modules. The digital output must be assigned to one of these I/O modules. ECOLOG-PRO I/O modules or the Alarm Interface LAN can be used as I/O modules.

• I/O module channel
  Selection list with all channels available at this I/O module. The digital output must be connected to one of these channels to receive its measured values. Only the channels that are still free are listed.

• Digital output ID
  Serves as further parameter for identification besides the name of the digital output module. This ID is assigned by ELPRO during production of the module.

• Switch on test / Switch off test - test functions for the digital output.

General:

• Sensor Group Name
  Name of the sensor Group for monitoring a group of sensors easily with elproMONITOR. The sensor group must be provided with a unique name.

I/O Module:

• I/O Module Name
  Name of the I/O Module for monitoring with elproMONITOR and for easy identification in the reports. The I/O module must be provided with a unique name.

• Memo
  In this area, information such as location of the I/O Module or the data loggers connected to the I/O moidule can be added.

• I/O Module Type
  The type of the I/O Module can be selected from the drop down menu

I/O Module Type - Alarm Interface Ethernet - Obsolet

• IP Address
  Fixed IP address. The network administrator must assign the address to avoid network conflicts.

• Port Number
  2101

• I/O Module ID
  ID of the I/O Module that, the Alarm Interface Ethernet is using

• Ping
  This command checks the network settings of the I/O module and the network connection. The test is ended by an OK or NOK confirmation

I/O Module Type - Alarm Interface USB - Obsolet

• COM Port
  COM Port that the USB is connected

• I/O Module ID
  ID of the I/O Module that, the Alarm Interface USB is using

• Ping
  This command checks the network settings of the I/O module and the network connection. The test is ended by an OK or NOK confirmation

I/O Module ECOLOG-NET LP4, LH2, LA8, LR8,

• IP Address
  Fixed IP address. The network administrator must assign the address to avoid network conflicts.

• Port Number
  2101

• Ping
  This command checks the network settings of the I/O module and the network connection. The test is ended by an OK or NOK confirmation

I/O Module ECOLOG-PRO LBR

• I/O Module ID
  ID of the I/O Module that, the ECOLOG-PRO LBR is using

• IP Address / Hostname
  Fixed IP address / Hostname. The network administrator must assign the address to avoid network conflicts.

• Ping
  This command checks the network settings of the I/O module and the network connection. The test is ended by an OK or NOK confirmation

• Scan Bridge
  Scans the I/O Modules that is using the ECOLOG-PRO LBR as network bridge

  • I/O Module detected

    • Check and adapt the settings of the I/O modules

  • I/O Module removed
    Before saving, check whether the module configuration of the LBR in the elproMONITOR matches the hardware installation.
    Removing an I/O module by saving the parameters without removing the sensors will result in the configuration data being lost.
    The measured values will still be recorded, but after a restart raw milliamper values will be shown instead of - for instance - Celsius/Fahrenheit or relative humidity values.

I/O Module ECOLOG-PRO 1NTR

• I/O Module ID
  ID of the I/O Module that, the ECOLOG-PRO 1NTR

• RBR ID
  ID of the ECOLOG-PRO RBR that the ECOLOG-PRO 1NTR is paired with

• Network ID
  Identification of the elproMONITOR server

• Actual Signal to Noise Ratio (SNR)
  Shows the Signal to Noise ration of the Radio connection

• ID: ECOLOG-PRO 1NTR
  Unit can be edited from the Sensor Settings section

I/O Module ECOLOG-PRO 2PTR

• I/O Module ID
  ID of the I/O Module that, the ECOLOG-PRO 2PTR

• RBR ID
  ID of the ECOLOG-PRO RBR that the ECOLOG-PRO 2PTR is paired with

• Network ID
  Identification of the elproMONITOR server

• Actual Signal to Noise Ratio (SNR)
  Shows the Signal to Noise ration of the Radio connection

• ID: ECOLOG-PRO 2PTR
  Unit can be edited from the Sensor Settings section

I/O Module ECOLOG-PRO 1TRH

• I/O Module ID
  ID of the I/O Module that, the ECOLOG-PRO 1TRH

• RBR ID
  ID of the ECOLOG-PRO RBR that the ECOLOG-PRO 1TRH is paired with

• Network ID
  Identification of the elproMONITOR server

• Actual Signal to Noise Ratio (SNR)
  Shows the Signal to Noise ration of the Radio connection

• ID: ECOLOG-PRO 1TRH
  Temperature unit can be edited from the Sensor Settings section
  Humudity Unit can be selected from the dropdown menu

I/O Module Lighthouse Particle Counter

• IP Address
  Fixed IP address. The network administrator must assign the address to avoid network conflicts.

• Port Number
  502

• I/O Module ID
  ID of the Particle Counter

• Flowrate, Preset at the Particle Counter Configuration

• Product Name
  Preset at the Particle Counter Configuration

• Model Name
  Preset at the Particle Counter Configuration

• ID:
  Preset at the Particle Counter Configuration

Sensor Limit Profile:

• Sensor Limit Profile Name
  Name of the Sensor Limit Profile for monitoring with elproMONITOR and for easy identification in the reports. The Snesor Limit Profile must be provided with a unique name.

• Lower Limit
  In this area, the lower limit value which is not considered as deviation can be entered.

• Lower calculated limit
  

• Lower the lower limit value which is not considered as deviation can be entered.

• Lower calculated limit
  Calculated Limit is for setting a relation with Humudity Limit based on different temparatures. If customer wants to set up variying humudity limits based on temparature, here it is possible to set the equvation to calculate variying humudity limits changing with temperature value.

• Lower Limit Delay
  Number of intervals that the Lower Limit value should be exceeded before elproMONITOR informs user about the deviation can be entered here

• Upper Limit
  In this area, the upper limit value which is not considered as deviation can be entered

• Upper Calculated Limit
  Calculated Limit is for setting a relation with Humudity Limit based on different temparatures. If customer wants to set up variying humudity limits based on temparature, here it is possible to set the equvation to calculate variying humudity limits changing with temperature value.

• Upper Limit Delay
  Number of intervals that the Upper Limit value should be exceeded before elproMONITOR informs user about the deviation can be entered here

• Consider logging intervals…
  Entering a tick causes invalid values (no connection, sensor failure) to be taken into consideration as a violation of the alarm

Sensor Issue Profile:

• Sensor Issue Profile Name
  Name of the Sensor Issue Profile for monitoring with elproMONITOR and for easy identification in the reports. The Sensor Issue Profile must be provided with a unique name.

• No Connection Alarm
  The alarm is activated only by ticking the hook.

• No Connection Delay
  Number of intervals that the No Connection Failure should occure before elproMONITOR informs user about the issue can be entered here

• Sensor Failure
  The alarm issue is activated only by ticking the hook.

• Sensor Failure Delay
  Number of intervals that the Senfor Sensor Failure should occure before elproMONITOR informs user about the issue activates the deviation, can be entered here

• Low Battery Notification
  The alarm issue is activated only by ticking the hook.

• Radio Strenght Warning
  The alarm issue is activated only by ticking the hook.

• Radio Strenght Warning Delay
  Number of intervals that the poor radio strenght should occure before elproMONITOR informs user about the issue activates the deviation, can be entered here

• Signal to Noise Ratio Threshold
  The user defined value to set the custom radio strenghtstreng; taking in to account the ratio between, signal and noise level.

• One of the following options should be selected to set the alarm level for radio strenght

  • Weak Radio Strenght

  • Bad Radio Strenght

  • Custom Radio Strenght

Digital Input Profile:

• Digital Input Profile Name
  Name of the Digital Input Profile for monitoring with elproMONITOR and for easy identification in the reports. The Digital Input Profile must be provided with a unique name.

• I/O Module Type
  Here the correct I/O Module type can be selected. Options are ECOLOG-PRO 4DI or ECOLOG-NET

• Mode
  Here the Log mode can be selected, there following options available

  • STANDARD The contact status is used as an alarm criterion.status at the moment when the interval was started is shown by the Digital Input

  • TIME MONITORING The duration of the contact status (open, closed) as a percentage of the logging interval is used as the alarm criterion activation is shown by the Digital Input (min. 200 ms)

  • EDGE COUNTER The number of contact status changes (rising, falling) per logging interval is used as the alarm criterion activationmis shown by the Digital Input (min. 200 ms)

• Text if Input=1 or 0
  Text field for entering the message text

• Logic
  Alarm if Input = 1 Switch between contact input 1 or 2 and GND closed
  Alarm if Input = 0 Switch between contact input 1 or 2 and GND openAlarms if the Digtial Input Status changes from 0 to 1
  Alarm if Input = 0 Alarms if the Digital Input Status changes from 1 to 0

• Delay
  Delay time, enter in logging interval steps

Mode Time Monitor:

• Border greater than, Border less than
  Limit values in % of the logging interval.

• Text if outer Border, Text if inner Border
  Text field for entering the message text

Mode Edge Counter:

• Border Greater Than, Border less than
  Limit values in number of edge changes.

• Text if outside limits, Text if inside limits
  Text field for entering the message text.

Create New Recipient Profile:

• Recipient Profile Name
  Name of the Recipient Profile for monitoring with elproMONITOR and for easy assigning of the recipients. The Recipient Profile must be provided with a unique name.

• E-Mail
  The e-mail alarm is activated by ticking the checkbox. All information needed to identify an issue is automatically contained in the e-mail
  To, Cc, Subject: This information is used to address the e-mail.
  Text This field should contain information such as process information, responsibilities, and instructions, and is attached to each e-mail. Relevant Information can be added by selecting from the menu on the right side of the Text field. As default all informations are selected

• Send Test E-Mail is to test the functions
  

Aggregated Alarm Email:

This option is used to receive a summary of the active and/or inactive deviations in a specific time period as an e-mail. This means the sensor must be configured accordingly in order to obtain a deviation
The aggregated email alarm is activated by ticking the checkbox

• Aggregation Interval of Change
  Interval time as minutes can be selected from the drop down menuI/O Module Type
  Here the correct I/O Module type can be selected. Options are ECOLOG-PRO 4DI or ECOLOG-NET can be selected from the drop down menu

• To, Cc, Subject: This information is used to address the e-mail.
  Text This field should contain information such as process information, responsibilities, and instructions, and is attached to each e-mail. Relevant Information can be added by selecting from the menu on the right side of the Text field. As default all informations are selected

• Send Test Aggregated E-Mail is to test the functions
  

SMS:
The SMS alarm is activated by ticking the checkbox

• SMS Number
  The mobile phone number that elproMONITOR should send the alarm information to.

• SMS Text
  This field should contain information such as process information, responsibilities, and instructions, and is attached to each SMS. Relevant Information can be added by selecting from the menu on the right side of the Text field. As default all informations are selected

• Send Test SMS is to test the functions

Digital Outputs:

• Digital Output 1, Digital Output 2
  Selection list of configured digital outputs.

• Plugin
  Plugin, Parameters: This is a customer-specific software module. It is produced by Elpro-Buchs AG

• Test Plugin is to test the functions

Repeat Notification:
The Repeat Notification is activated by ticking the checkbox

• Repeat Notification Integral
  The interval time in minutes can be input here